Simulation of an Exoskeleton with a Hybrid Linear Gravity Compensator

Purpose of research. Development of a mathematical model of an exoskeleton equipped with a hybrid linear gravity compensator (HLGC), dynamic analysis on the example of a typical exoskeleton application scenario (in the process of lifting a load), obtaining time patterns of changes in system parameters, including electric drive torques allowing assessment of power plan power consumption and energy efficiency. The article deals with the challenging issue of improving the efficiency of the exoskeletal suit by means of HLGC. The use of a hybrid approach makes it possible to increase the efficiency of assisting the exoskeletal suit when performing various technological operations, for example, when lifting a load, when tilting and holding.
Methods. When developing a mathematical model, an original approach was used to form the motion trajectory of the exoskeleton sectors during operation, based on the use of seventh-order polynomials. The paper uses a mathematical model represented by a system of second-order differential equations that connects the moments acting on the operator and the exoskeleton, the angular accelerations of the operator's back and the exoskeleton.
Results. During numerical simulation, time diagrams of changes in system parameters, angles of rotation of exoskeleton hinges, moments that occur in a hybrid LGC, as well as graphs of current consumption of engines when performing lift and tilt with a load are obtained.
Conclusion. In the course of the research, a kinematic model of an exoskeleton suit equipped with a GLGC was developed, second-order differential equations describing the dynamic behavior of the electromechanical system were written, and numerical simulation was performed to estimate the forces and energy consumption in the exoskeleton hinges and the drive of the hybrid linear gravity compensator.

1. Korenevskiy N. A. et al. Ekzoskelet s biotekhnicheskoi obratnoi svyaz'yu dlya vertikalizatsii patsientov [An exoskeleton with biotechnical feedback for verticalization of patients]. Meditsinskaya tekhnika = Biomedical Engineering, 2017, vol. 51, no. 4, pp. 285-289 (In Russ.).

2. Yatsun S.F., Savin S.I., Emelyanova O. V., Yatsun A.S., Turlapov R.N. Ekzoskelety: analiz konstruktsii, printsipy sozdaniya, osnovy modelirovaniya [Exoskeletons: analysis of structures, principles of creation, foundations of modeling]. Kursk, 2015. 179 p. (In Russ.).

3. Jatsun S.F., Al Maji Kh.Kh.M., V Pavlovsky.E., Yatsun A.S., Karlov A.E., Saveleva E.V. Analysis of the effect of the exoskeleton geometrical dimensions on the nature of a linear compensator operation. Developments in eSystems Engineering 2019, Robotics, Sensors and Industry 4.0. Kazan, 2019.

4. Plagenhoef Stanley, Gaynor Evans F., Thomas Abdelnour. Anatomical data for analyzing human motion. Research quarterly for exercise and sport, 1983, 54, no. 2, pp. 169-178.

5. Spada S. et al. Analysis of exoskeleton introduction in industrial reality: main issues and EAWS risk assessment. International Conference on Applied Human Factors and Ergonomics, Springer, Cham, 2017, pp. 236-244.

6. Theurel J., Desbrosses K., Roux T., Savescu A. Physiological consequences of using an upper limb exoskeleton during manual handling tasks. Applied ergonomics, 2018, no. 67, pp.211-217.

7. Ulrey B. L., Fathallah F. A. Subject-specific, whole-body models of the stooped posture with a personal weight transfer device. Journal of Electromyography and Kinesiology, 2013, vol. 23, no. 1, pp. 206-215.

8. Strausser K. A., Kazerooni H. The development and testing of a human machine interface for a mobile medical exoskeleton. 2011 IEEE/RSJ International Conference on Intelligent Robots and Systems. IEEE, 2011, pp. 4911-4916.

9. Talaty M., Esquenazi A., Briceno J. E. Differentiating ability in users of the ReWalk TM powered exoskeleton: An analysis of walking kinematics. 2013 IEEE 13th International Conference on Rehabilitation Robotics (ICORR), IEEE, 2013, pp. 1-5.

10. Esquenazi A. et al. The ReWalk powered exoskeleton to restore ambulatory function to individuals with thoracic-level motor-complete spinal cord injury. American Journal of Physical Medicine & Rehabilitation, 2012, vol. 91, no. 11, pp. 911-921.

11. Neuhaus P. D. et al. Design and evaluation of Mina: A robotic orthosis for paraplegic. 2011 IEEE International Conference on Rehabilitation Robotic, IEEE, 2011, pp. 1-8.

12. Yan T. et al. Review of assistive strategies in powered lower-limb orthoses and exoskeletons. Robotics and Autonomous Systems, 2015, vol. 64, pp. 120-136.

13. Sankai Y. HAL: Hybrid assistive limb based on cybernics. Robotics research. Springer, Berlin, Heidelberg, 2010, pp. 25-34.

14. Farris R. J., Quintero H. A., Goldfarb M. Preliminary evaluation of a powered lower limb orthosis to aid walking in paraplegic individuals. IEEE Transactions on Neural Systems and Rehabilitation Engineering, 2011, vol. 19, no. 6, pp. 652-659.

15. Yatsun S.F., Antipov V.M., Karlov A.E. Modelirovanie pod"ema gruza s pomoshch'yu promyshlennogo ekzoskeleta [Modeling of Loading by Industrial Exoskelet]. Izvestiya Yugo-Zapadnogo gosudarstvennogo universiteta = Proceedings of the Southwest State University, 2018; 22(6): 14-20 (In Russ.). DOI: 10.21869/2223-1560-2018-22-6-14-20.

16. Yatsun S. F., Antipov V. M., Karlov A. Ye., Al Manji Hamil Hamed Mohammed. Load Lifting in the Exoskeleton with Gravity Compensation. Izvestiya Yugo-Zapadnogo gosudarstvennogo universiteta = Proceedings of the Southwest State University. 2019; 23(2): 8-17 (In Russ.). DOI: 10.21869/2223-1560-2019-23-2-8-17.